INTRAME TM 350 asfaltcentrale

INTRAME TM 350 asfaltcentrale
Foto: INTRAME TM 350 asfaltcentrale
1/1
Vergelijken Aan favorieten toevoegen PDF
Prijs:
op aanvraag
Merk INTRAME
Model TM 350
Type asfaltcentrale
Jaar 2004
Eerste registratie 1994
Standplaats Spanje Madrid
Datum van invoering vandaag
Autoline ID ZL13655
Beschrijving
Capaciteit 350 t/h
Conditie
Conditie gebruikt
Banner
Overige details: Spaans
INTRAME 350 mt - 1994 + total renewed 2004

1. Cold bin Feeders - Composed of:
Eight hoppers total capacity of 80 m3 with spouts, belt feeder with variable speed (with control and regulation control booth) tape collection of 40 m in length, width 650 mm motor-driven 10 hp.
Each hopper carries a geared motor driven with variable speed feeder 3 HP
It features:
- antipollution separators
- Bars in Spout
- reversible metal frame to avoid the concrete wall

2. Dryer UNIT Composed of
Introducer tape arid cold engine powered 5.5 HP. Rotary drum dryer 2,750 mm diameter, 11,000 mm length with four-wheel driven rollers with geared motors of 40 hp each.
Tire tread on self-aligning roller. Canjilones, appropriately, type "saw tooth" in the initial part of the drum, in order to get a thick curtain of aggregates throughout the dryer section and get higher performance in drying aggregates.
Medium pressure burner, model UF-100 with built-in pump and turbo blower power, powered by two electric motors 60 and 30 CV of 25,000,000 Kcal / h and 1,820 kg / h of maximum consumption of fuel oil.
Hot aggregate elevator vertical type and closed with 395mm x 203mm buckets mounted on pulleys 101 chain wheel and electric motor drive 60 C.V.

3. METERING UNIT AND MIXER.- Composed of:
inclined screen, with five vibrant trays and bypass.
The screens are closed, but are easily accessible for inspection and replacement of fabrics.
It has two electric motors 25 C.V. each, and the transmission is located outwardly so that it does not affect heat or filler.
Classification Silo hot.
Divided into five compartments, with a capacity of 60 m3 equipped with a suction duct connected to the general collector powder.
Sluice gate pneumatic drive.
collecting excess of rejection and gutters.
Dosing hopper weight of the aggregate, mounted on three compression strain cells, the scale capacity is 7,000 Kg
Pneumatically operated discharge gate.
Dosage reservoir by weight bitumen, by bending strain cell and a capacity of 400 Kg.
Filling and discharge valves pneumatically operated heated by hot oil.
Paddle mixer, model 350. 4.500 kg, low speed.
twins synchronized axes.
Jacketed heating oil, which form an integral part of the mixer must be removed and not to change the coatings.
Pallets and interior coatings, abrasion resistant and easily replaceable alloy through the inspection door of the mixer.
Electric motor drive 150 C.V.
The engine and gearbox are directly coupled to the mixer gears via roller chains and sprockets. Processing gears are installed so that the engine power is equally distributed on the twin axes instead of on one axis.
The gate of the mixer is watertight and is mounted to slide and adjustable slack pneumatic cylinder actuator is oversized.
Tower.-
The legs and stands are folding tower, robust and welded steel, providing great stability and eliminate vibration.
The tower is designed and dimensioned to allow passage of trucks and their cargo under the mixer (3.50 m).
Platform height scales with access stairs and walkways.
Footbridges platform at the height of the sieves.
Platform with walkways to inspect the height of the silo hot.
Platform walkways in the hot elevator.
Staircase with security guards from the first platform to the screens.
The floors of the platforms are skid plate.
TEMPERATURE INDICATOR.-
Pyrometer temperature indicator aggregates at the dryer outlet.
TEMPORIZADORES.-
To set the time of dry and wet mixing as well as to determine the opening time of the discharge gate mixer.

4. TEAM RECOVERY AND PURIFICATION FILLER.-
Compound:
Mobile filter sleeves FE-1020 model with independent impacts collector with 950 m2 of Nomex bag filter surface
- Two augers for driving the bag house filler, filler to lift driven by electric motor 5.5 C.V.
- Three augers lead the bulk filler from the collector to the hot elevator impacts
- Extractor fan JMA-165, driven by motor 220 C.V.
- Floodgate extractor fan 0.25 C.V.
DOSAGE OF EQUIPMENT FILLER
Compound:
Io) Filler recovered.
- A vertical silo capacity of 50 tons with a horizontal endless evacuator,
powered by 7.5 HP engine
- An elevator bucket vertically closed, motor driven 10 C.V.
- Endless engine powered by 7.5 hp. leading to the filler weighing hopper.
- Endless evacuator abroad, the excess filler motor driven 7.5 C.V.
2o) Filler contribution:
- A vertical silo of 50 MT capacity with evacuator horizontally endless, motor-driven 7.5 hp.
- A motor driven endless 7.5 HP carrying the filler to a weighing hopper.
3O) Hopper weighing recovery v filler filler:
- With capacity of 450 kg and 0.25 kg graduations heavy strain cells
- Equipped with three cumulative cuts.

5. CIRCUIT BETÚN.-
Bitumen stored in tanks, is metered through a pump system of continuous operation pouring into a cuvette with heavy end by cutting three-way valve bifurcating excess by the return to the tank.
Bitumen pump from the storage tanks to the bucket weighing oil heated electric motor driven 20 C.V.
INJECTION BETÚN.-
On the mixer, including:
- Pump heating oil bitumen electric motor powered by 25 hp.
- Spray bar and pneumatically operated valves.

6. EQUIPMENT COMMAND AND CONTROL AUTOMATIC PLANT.-
Electronic. Prepared four aggregates, bitumen and two filler. With one or more preset dosage, and includes:
- Count kneaded
- Setting a number of automatic repeat batches
- Tote kneaded
- Counter download times
- Regulation and checking the error limits on heavy.

7. EQUIPMENT COMMAND AND CONTROL AUTOMATIC QUEMADOR.
Mail and with the following features and elements:
- Pyrometers, daily indicator and temperature recorder aggregates.
- Automatic fire Modulator for temperature
Preset within the required tolerances. It provides great fuel economy and prevents overheating of the mixtures.
- Pyrometer temperature indicator of the exhaust chimney with security mechanisms that cut combustion if exceeded one (adjustable at will) limit deemed as dangerous to bad thermal performance.

8. INSTALLATION OF AIR COMPRIMIDO.-
For operating the plant. Comprises pressure regulator connection tubing, filters, gauges, strainers, etc.
In Addition to a compressor provided With continuous control driven by a motor 100 C.V. 380 V. Maximum operating pressure of 7 Kg / cm2

9. Heating Central.-
V.12 DM.300 Model Approved by the Ministry of Industry.
With a heat capacity of 800,000 Kcal / h at a maximum temperature of 210 ° C
Fast performance is due to the incorporation of a helical coil Which Dramatically Improves the heat exchange surface.
Oil circulation is effected by Means of a centrifugal pump 2 "driven electric engine 10hp.

10. INSTALLATION ELÉCTRICA.-
The electrical installation, including wiring of the entire plant and its corresponding elements together.
The entire installation is supplied with AC 380 V 50 Hz
- Wardrobe, includes the full picture of distribution starters for all motors supplied with the plant.
- Breakers with thermal-magnetic circuit protection on each motor.
Thermal protection relays on each motor circuit.
- General Switches
- Transformers for 110 V. For operation of all controls installation.

11. DESCRIPTION OF OTHER AUXILIARY ELEMENTS PLANT.-
STORAGE BETÚN.-
Formed by 3 cylindrical tanks, thermally insulated externally, vertical, provided with heating coil circulation of thermal oil, carrying manhole ventilation and other safety survey and sleeves.
Each of the tanks, leading automatic regulation of the temperature of the bitumen.
They are stamped pressure of 2 kg / cm2.
Its capacity is each 80 m3.
FUEL STORAGE OIL.-
Formed by 1 air tank, 80 m3 cylindrical with dished ends, thermally insulated externally, vertical, provided with heating coil circulation of thermal oil, Campsa manhole type, carrying a vertical vent finished in a firewall; I return ducts for feeding and.
cubeto externally one of equal capacity and the tank is mounted sink drain.
BITUMEN PUMP DISCHARGE CAMIONES.-
For pumping bitumen tankers to storage tanks provided with a suction Campsa type 3 ". It is sectioned by a motor 20 C.V.
Deze aanbieding is enkel een richtlijn. Vraag de verkoper voor meer informatie.
Verstuur uw vraag